Rust on the water heater is an indication that your unit needs to be fixed or replaced. If you feel hesitant because electricians and plumbers create so much fuss the only option left to you is that you need to do it yourself. You can learn how to wire a hot water heater by following the steps that are enlisted.
Wiring from installation to breaker has a simple skill. Mostly, you will need to execute the neat wiring while joining the primary wire and ground wires to their designated place in the heater as well as the circuit breaker.
If you have gotten a new water heater and are willing to install it yourself, this guide is for you. It will guide you to perform it neatly and effectively.
8 Steps Guide to Wire a Hot Water Heater
In order to begin the process, you need to collect the entire tools once, which may include a screwdriver, wrench, pipe cutter, circuit breaker, voltage tester, flexible hose, etc. However, before beginning the process open the faucet and let the remaining water in the pipes drain. Do it for both hot and cold pipes. Now let’s start the wiring process.
1. Cut off the Primary Sources of Electric Supply
As all electrical support ought to be, closing down the primary power source is the essential step. This procedure is fundamental for getting a free hand on the wires without the danger of electrical risks. Then again, to stop the water, turn off the wrench of the primary line that provisions your home.
2. Drain the Excess Water
When you cut off the running water, the time has come to eliminate the pressure from your lines. Open a couple of fixtures and let all the leftover water inside the pipelines drain away. As you do this, remember to deplete lines of the two temperatures, hot and cold. Allow them to run for a couple of moments to avoid splashes.
3. Install the Circuit Breaker
Prior to introducing the committed CB for your electric water warmer, get your voltage analyzer and guarantee everything is disconnected. It is the primary rule of learning how to wire a hot water heater.
No power ought to be accessible from each bus bar to the wiring screws, with your voltage analyzer showing a green light. When you are allowed to go, cautiously connect the breaker to the bus bar until you hear a clicking sound.
4. Run the Wirings
Plan how you need to run your wirings from the breaker box to your Electrical Metallic Tubing (EMT) or electrical flex interfacing with the water tank. Conveniently secure your wires on the wall or at the roof if required with a course clasp.
You can allude to an electrically heated water storage wiring graph in order to thoroughly comprehend the association between your breaker and the radiator. In any case, if the past writings are still OK, you can avoid this methodology.
5. Wire in the Circuit Breaker
Associate your 10 AWG wires to the breaker. Strip a little piece of the cable. Make sure to leave a sufficient length of wire and not cut entirely through. Begin associating the hot wires on the two posts of the CB. Then, at that point, screw in the ground wire to its different spot.
6. Wire in the Hot Water Heater
Cross the wires from the Electrical Metallic Tubing to the opening of your water heaters’ intersection box. When you join your wires through the intersection cover, strip the protection for around .75 mm. Get your wires through the connector and clasp the NM cables sheathe.
Interface the ground wire to the ground screw inside the intersection box. Curve the dark wire of your circuit around a water radiator wire.
Utilize a wire nut to seal them up. Observe your board’s white wire and imprint it with tape to connote its status as a hot wire. Subsequently, interface this white wire to one more wire of the water heater.
7. Open the Primary Pipe and Fill the Tank
Guarantee that everything is fixed, from the PVC lines to the wiring lines, inside or outside the intersection box. Turn the water source on and fill the tank first prior to turning on the electrical warming component. Then, at that point, decompress the lines by allowing every one of your fixtures to run for three minutes.
8. Turn on the Principle Breaker Box
Switch on the main electrical board and the devoted electrical switch for the water heater. For safety measures, utilize the voltage analyzer to find any electrical holes outside your tank. Checking incorporates metal parts like intersection covers and screws.
For a couple of updates, consistently check the tank’s water warming component, top, and base.
In the direst outcome imaginable where frozen lines happen, the warming component will run even with a drained water source. This disregard brings about harm because of overheating. On the off chance that you want a substitution, ensure everything is as old as past arrangements.
Conclusion
It is easy to buy a water heater, but getting it installed is an even longer process. In order to avoid inconvenience and get them installed right on hand, you can learn how to wire a hot water heater. It is an easy and straightforward skill that anyone can acquire.
We have mentioned a simple guide that ensures your safety and guides you from the start till the end. As the electricity is involved in this process, you have suggested double-checking the wires after cutting the power supply off.